wiki:OpenFlow/Slicer/TestPlan/Results/FlowspaceFirewall/1.0.4b

Version 12 (modified by tupty@bbn.com, 8 years ago) (diff)

--

  1. OpenFlow Slicer Test Plan Results
  2. Results Legend
  3. OF-OPR-SLCR-FN Testing
    1. Results
      1. Step 1: Setup
      2. Step 2: Establish that basic connectivity works
      3. Step 3: Test for VLAN enforcement and translation
      4. Step 4: Check data plane throughput
      5. Step 5: Test for OF functionality
      6. Test 6: Test for stacked slicer support
      7. Test 7: Test for any extra functionality
      8. Test 8: Test management API
    2. Logs
  4. OF-OPR-SLCR-OP Testing
    1. Results
      1. Step 1: Setup
      2. Step 2: Collect monitoring data
      3. Step 3: Test slice operations
      4. Step 4: Substrate-generated traffic
      5. Step 5: Test logging
    2. Logs
  5. OF-OPR-SLCR-SW Testing
    1. Results
      1. Step 1: Perform validation steps
    2. Logs
  6. Integration Testing
    1. Results
      1. Step 1: Setup
      2. Step 2: Collect monitoring data
  7. Wishlist Testing
    1. Results
      1. Step 1: Check documentation
      2. Step 2: Set up the environment
      3. Step 3: Test that priority setting works
    2. Logs

OpenFlow Slicer Test Plan Results

This page tracks the results of a piece of software run through the ​OpenFlow Slicer Test Plan.

SoftwareVersion

Results Legend

Individual test case status may be one of the following:

OF-OPR-SLCR-FN Testing

Results

Step 1: Setup

Test CaseResultNote
1.a.i. Color(green,Pass)?
1.a.ii. Color(green,Pass)?
1.a.iii. Color(green,Pass)?
1.a.iv. Color(green,Pass)?
1.a.v. Color(green,Pass)?
1.b. Color(green,Pass)?
1.c. Color(green,Pass)?

Step 2: Establish that basic connectivity works

Test CaseResultNote
2.a. Color(green,Pass)?
2.b. Color(green,Pass)?
2.c. Color(green,Pass)?
2.d. Color(green,Pass)?
2.e. Color(green,Pass)?
2.f.i. Color(red,Fail)? Slicer capture​. This failure might be an issue with environment setup. Is slicer responsible for installing a "drop unmatched" rule?
2.f.ii. Color(green,Pass)?Slicer capture​
2.f.iii. Color(green,Pass)?Slicer capture​, Controller capture​
2.f.iv. Color(green,Pass)?Slicer capture​, Controller capture​
2.f.v. Color(green,Pass)?Slicer capture​, Controller capture​
2.g. Color(green,Pass)?

Step 3: Test for VLAN enforcement and translation

Test CaseResultNote
3.a. Color(green,Pass)?
3.b. Color(green,Pass)?Controller capture​
3.c. Color(green,Pass)?Controller capture​
3.d. Color(green,Pass)?
3.e. Color(green,Pass)?

Step 4: Check data plane throughput

Test CaseResultNote
4.a. Color(green,Pass)?
4.b. Color(green,Pass)?
4.c. Color(green,Pass)?
4.d. Color(green,Pass)?
4.e. Color(green,Pass)?

Step 5: Test for OF functionality

Test CaseResultNote
5.a. Color(green,Pass)?
5.b. Color(green,Pass)?
5.c. Color(green,Pass)?
5.d.i. Color(red,Fail)?​Known issue, will be fixed in next release. We should look into other similar instances where symmetric messages which are served by FSFW (and not the substrate) appropriately set the XID.
5.d.ii.
5.d.iii.
5.e.
5.f.i.
5.f.ii.

Test 6: Test for stacked slicer support

Test CaseResultNote
6.a. Color(green,Pass)?
6.b. Color(green,Pass)?

Test 7: Test for any extra functionality

Test CaseResultNote
7.a. Color(#98FB98,Pass: most criteria)?Controller capture​, Limits seem to be enforced. Cases in which slice is disabled don't seem to be documented. Specific types of OF error messages sent in different cases don't seem to be documented.
7.b. N/A No data plane limiters.
7.c. Color(#98FB98,Pass: most criteria)?Controller capture​, Limits seem to be enforced. Cases in which slice is disabled don't seem to be documented. Specific types of OF error messages sent in different cases don't seem to be documented.

Test 8: Test management API

Test CaseResultNote
8.a. Color(orange,Blocked)? Management API software under development.
8.b. Color(orange,Blocked)? Management API software under development.
8.c. Color(orange,Blocked)? Management API software under development.
8.d. Color(orange,Blocked)? Management API software under development.

Logs

Fill these in as needed

OF-OPR-SLCR-OP Testing

Results

Step 1: Setup

Test CaseResultNote
1.a.
1.b.

Step 2: Collect monitoring data

Test CaseResultNote
2.a.

Step 3: Test slice operations

Test CaseResultNote
3.a.
3.b.
3.c.
3.d.
3.e.

Step 4: Substrate-generated traffic

Test CaseResultNote
4.a.
4.b.

Step 5: Test logging

Test CaseResultNote
5.a.
5.b.
5.c.
5.d.
5.e.

Logs

Fill these in as needed

OF-OPR-SLCR-SW Testing

Results

Step 1: Perform validation steps

Test CaseResultNote
1.a.
1.b.
1.c.
1.d.
1.e.

Logs

Fill these in as needed

Integration Testing

Results

Step 1: Setup

Test CaseResultNote
1.a.
1.b.
1.c.
1.d.

Step 2: Collect monitoring data

Test CaseResultNote
2.a.

Wishlist Testing

Results

Step 1: Check documentation

Test CaseResultNote
1.a.
1.b.
1.c.

Step 2: Set up the environment

Test CaseResultNote
2.a.
2.b.
2.c.

Step 3: Test that priority setting works

Test CaseResultNote
3.a.
3.b.
3.c.
3.d.

Logs

Fill these in as needed

Attachments (19)

Download all attachments as: .zip