== !AmariSoft LTE ==


The image used for this experiment is 'baseline.ndz'. In this tutorial we will use nodes equipped with Netgear AC341u LTE dongles. The basestation is Amarisoft running on Bsc03out.

During a normal experiment using OMF, the following actions are scripted and automated. This is a look at the steps involved in something as simple as starting an LTE connection behind the scenes.

You will run the following commands on node7-1.grid.orbit-lab.org, node1-7.grid.orbit-lab.org, node19-3.grid.orbit-lab.org

After connecting to the grid console:
1. {{{ omf load -i baseline.ndz -t node7-1.grid.orbit-lab.org }}}[[BR]]

2. {{{ omf tell -a on -t node7-1.grid.orbit-lab.org }}}[[BR]]

3. It will take roughly 60 seconds to come up.[[BR]]

4. {{{ ssh root@node7-1.grid.orbit-lab.org }}}[[BR]]

5. {{{ modprobe GobiSerial }}}[[BR]]

6. {{{ modprobe GobiNet }}}[[BR]]

7. {{{ minicom -D /dev/ttyUSB1 }}}[[BR]]

8. {{{ AT!ippassthrough? }}}[[BR]]

9. It should return 1[[BR]]
 
 1. If it does not, run {{{ AT!ippassthrough=1 }}} then {{{ AT!reset }}}[[BR]]
 2. {{{ AT!entercnd="A710" }}}[[BR]]
    You should see {{{ OK }}}[[BR]]
 3. {{{ AT!dxcfg=wwan,connect,11 }}}[[BR]]
    You should see {{{ OK }}} then {{{ $QCRMCALL: 1, V4 }}} [[BR]]
 4. {{{ at!gstatus? }}} [[BR]]
     Will return a status like: [[BR]] 

{{{

at!gstatus?                                                                                                         
!GSTATUS: 
Current Time:  10049            Temperature: 42
Bootup Time:   0                Mode:        ONLINE         
System mode:   LTE              PS state:    Attached     
LTE band:      B25              LTE bw:      10 MHz  
LTE Rx chan:   8365             LTE Tx chan: 26365
EMM state:     Registered       Normal Service 
RRC state:     RRC Connected  
IMS reg state: No Srv  

RSSI (dBm):    -83              Tx Power:    0
RSRP (dBm):    -117             TAC:         0001 (1)
RSRQ (dB):     -10              Cell ID:     01A2D001 (27447297)
SINR (dB):      1.6

}}}

5. Exit Minicom by **PRESSING** {{{ Ctrl+A followed by x }}}, then {{{enter}}} to select ok.[[BR]]
{{{ dhcpcd eth2 }}} followed by {{{enter}}} to get a new line. [[BR]]

6. You should get an address in the 192.168.3.0/24 subnet. [[BR]]
 {{{ ping 192.168.3.1 }}}

7. You have successfully communicated with the basestation. [[BR]]

8. You can cancel the ping with {{{Ctrl+C}}} [[BR]]

9. {{{iperf -c 192.168.3.1 }}}
  This will report your bandwidth to the basestation.[[BR]]


10.  Uses rest interface to manage the BS. To set the LTE connection bandwidth to 5 MHz issue the following commands on the console (not node):

{{{
wget http://bsc03out.orbit-lab.org:5054/bscontrol/bs/1/default_cell_parameters?n_rb_dl=25     
wget http://bsc03out.orbit-lab.org:5054/bscontrol/bs/1/restart
}}}

Setting n_rb_dl to 50 sets it to 10 MHz while setting it to 100 sets the bandwidth to 20 MHz. After basestation restarts, most of the clients need to be also reconnected.