wiki:HowTo/ConfigureOVSStaticRouteMirroringNoController

Version 5 (modified by joshua.fasching@raytheon.com, 7 years ago) (diff)

--

This howto demonstrates how to set up static IP traffic between two hosts connected to an OVS switch without running a seperate controller. This tutorial uses custom OpenFlow table rules.

This howto uses the following rspec: https://raw.githubusercontent.com/GENI-NSF/geni-tutorials/master/OVSRyu/openflowovs-all-xen.rspec.xml

This rspec creates a network with 3 nodes: host1, host2, host3; connected to an OVSwitch ovs.


This tutorial will establish rules for allowing IP traffic to flow between host1 and host2.

Later in the tutorial we will discuss how to setup the ovs switch to allow for host3 to observe the traffic between host1 and host2 using the Mirror feature of the ovs switch. This could be used for network monitoring setups.

Setting up the static IP traffic

Configure OVS Switch

  1. Login to the OVS host
  2. Create an Ethernet bridge that will act as our software switch:
    sudo ovs-vsctl add-br br0
    
  3. Prepare the interfaces to be added as ports to the OVS switch
    • Your OVS bridge will be a Layer 2 switch and your ports do not need IP addresses. Before we remove them let's keep some information
      • Run ifconfig
      • Write down the interface names that correspond to the connections to your hosts. The correspondence is
        • Interface with IP 10.10.1.11 to host1 - ethX
        • Interface with IP 10.10.1.12 to host2 - ethY
        • Interface with IP 10.10.1.13 to host3 - ethZ
    • Remove the IP from your data interfaces.
      Be careful not to bring down eth0. This is the control interface, if you bring that interface down you won't be able to login to your host. For all interfaces other than eth0 and l0 (your interface names may vary) run :
      sudo ifconfig ethX 0  
      sudo ifconfig ethY 0 
      sudo ifconfig ethZ 0 
      
  4. Add all the data interfaces to your switch (bridge).
    Be careful not to add interface eth0. This is the control interface. The other three interfaces are your data interfaces. (Use the same interfaces as you used in the previous step.)
    sudo  ovs-vsctl add-port br0 ethX 
    sudo  ovs-vsctl add-port br0 ethY 
    sudo  ovs-vsctl add-port br0 ethZ 
    
  5. Verify the three ports configured run:
    sudo ovs-vsctl list-ports br0
    
  6. We want our switch to act without a seperate controller thus setting it to operate as standalone.
    sudo ovs-vsctl set-fail-mode br0 standalone
    
  7. Trust but verify. You can verify your OVS settings by issuing the following:
    sudo ovs-vsctl show
    

Testing the connectivity between host1, host2 and host3

Initially the OVSwitch is setup to act like an L2 learning switch. We want to disable this behavior except for specific IP addresses

sudo ovs-ofctl del-flows br0

From host1

ping -c 10  host2

From host2

ping -c 10 host1

From host3

ping -c 10 host2

Each of these should be unreachable.

Setting up the static IP flows

With the switch set up we can now setup routing between host1 and host2

First we will add rules to allow the OVS switch to behave like a normal switch for IP traffic between the two hosts

sudo ovs-ofctl add-flow br0 priority=500,ip,nw_src=10.10.1.1,nw_dst=10.10.1.2,actions=normal
sudo ovs-ofctl add-flow br0 priority=500,ip,nw_src=10.10.1.2,nw_dst=10.10.1.1,actions=normal

ARP traffic will also need to be able to flow in order for the routes to each host to be learned.

sudo ovs-ofctl add-flow br0 "priority=500,arp,nw_dst=10.10.1.1 actions=normal"
sudo ovs-ofctl add-flow br0 "priority=500,arp,nw_dst=10.10.1.2 actions=normal"

The connectivity can then be tested with:

From host1

ping -c 10 host2

From host2

ping -c 10 host1

From host3

ping -c 10 host2

Pings between host1 and host2 should succeed whereas pings from host3 will fail.

Setting up mirroring of traffic from host1 and host2 to host3

This is done with a single command to ovs-vsctl. It can be done independent of the previous steps if only mirroring is of interest to the user.

ovs-vsctl -- set Bridge br0 mirrors=@m \
              -- --id=@ethX get Port ethX \
              -- --id=@ethY get Port ethY \
              -- --id=@ethZ get Port ethZ \
              -- --id=@m create Mirror name=mymirror select-dst-port=@ethX,@ethY select-src-port=@ethX,@ethY output-port=@ethZ

Where ethX and ethY are the names of the interfaces connected to host1 and host2 on the OVS node. ethZ is the interface on the OVS node that connects to host3

Verifying mirroring behavior

To observe the mirroring behavior 3 terminal windows will need to be opened.

In one terminal ssh into host1 and execute

nc -ul 24565

In one terminal ssh into host2 and execute

nc -u host1 24565

In one terminal ssh into host3 and execute

sudo tcpdump -i eth1 -vv -X

In the terminal with host2 type a message and hit return

A message

Observe that the message is received on host1. On host3 the packet was also received and we can observe the message "A message" inside of the packet.

Attachments (1)

Download all attachments as: .zip