[[PageOutline]] = University of California Los Angeles Stitching Confirmation Tests = This pages capture the detailed test logs for each test defined in the [wiki:GeniNetworkStitchingConfirmationTests New Site Stitching Confirmation Tests] page. For the sites status see the [wiki:GeniNetworkStitchingConfirmationTestStatus New Site Stitching Confirmation Tests Status] page. == IG-ST-1 New Site to GPO IG topology == The UCLA site advertises the following stitching details: {{{ protogeni chainANDTree false false 2014-11-18T18:36:25Z 2014-11-18T18:36:25Z 1000000 1000000 1000 1 urn:publicid:IDN+al2s.internet2.edu+interface+sdn-sw.losa.net.internet2.edu:e5/1:ucla-ig 10 1000000 1000000 1000 1 l2sc ethernet 1500 1610-1629 false }}} Experimenter may not need any of this data, but it is helpful to reference when trying to determine how many VLANs are delegated for stitching at the site or how much bandwidth can be requested. Create a slice and then create the stitched slivers with the RSpec [http://groups.geni.net/geni/browser/trunk/stitch-examples/UCLA/IG-ST-1-al2s.rspec IG-ST-1-al2s.rspec]: {{{ $ stitcher.py createsliver IG-ST-1 IG-ST-1-al2s.rspec -o 14:43:20 INFO : Configured logging from file /home/lnevers/gcf-2.7/src/gcf/stitcher_logging.conf 14:43:20 INFO : Reading slice IG-ST-1 credential... 14:43:21 INFO : Slice urn:publicid:IDN+ch.geni.net:ln-test+slice+IG-ST-1 expires on 2014-11-25 19:13:49 UTC 14:43:21 INFO : Using SCS at http://nutshell.maxgigapop.net:8081/geni/xmlrpc 14:43:21 INFO : Calling SCS... 14:43:23 INFO : Multi-AM reservation will include resources from these aggregates: 14:43:23 INFO : 14:43:23 INFO : 14:43:23 INFO : 14:43:23 INFO : 14:43:24 INFO : Stitcher doing createsliver at ... 14:43:40 INFO : ... Allocation at complete. 14:43:40 INFO : Stitcher doing createsliver at ... 14:43:59 INFO : ... Allocation at complete. 14:43:59 INFO : Stitcher doing createsliver at ... 14:44:05 INFO : ... Allocation at complete. 14:44:05 INFO : Stitcher doing createsliver at ... 14:44:51 INFO : DCN AM : must wait for status ready.... 14:44:51 INFO : Pausing 30 seconds to let circuit become ready... 14:45:31 INFO : DCN circuit 139241 is ready at 14:45:38 INFO : ... Allocation at complete. 14:45:38 INFO : All aggregates are complete. 14:45:38 INFO : Your resources expire at 2014-11-24T19:33:24 (UTC). 14:45:38 INFO : Saved combined reservation RSpec at 4 AMs to file '/home/lnevers/gcf-test/stitch-test/UCLA/IG-ST-1-manifest-rspec-multiam-combined.xml' Success: Reserved resources in slice IG-ST-1 at 4 Aggregates (including 2 intermediate aggregate(s) not in the original request), creating 1 stitched link(s). }}} Determined login information at each UCLA and GPO aggregate: {{{ $ readyToLogin.py IG-ST-1 -a ucla-ig .... ig-chic's geni_status is: ready User lnevers logs in to ig-chic using: ssh -p 31034 -i /home/lnevers/.ssh/geni_cert_portal_key lnevers@pc2.instageni.idre.ucla.edu $ readyToLogin.py IG-ST-1 -a gpo-ig .... ig-gpo's geni_status is: changing User lnevers logs in to ig-gpo using: ssh -p 33850 -i /home/lnevers/.ssh/geni_cert_portal_key lnevers@pc5.instageni.gpolab.bbn.com }}} === Measurements === '''Iperf InstaGENI GPO VM to InstaGENI UCLA VM (TCP) - TCP window size: 23.5 KByte (default)''' ''Collected: 2014-11-18'' __One Client_ {{{ }}} __Five Clients__ {{{ }}} __Ten Clients__ {{{ }}} '''Iperf InstaGENI GPO VM to InstaGENI UCLA VM (UDP) - UDP buffer size: 224 KByte (default) ''' {{{ }}} '''Ping from InstaGENI GPO VM to the InstaGENI UCLA VM ''' {{{ }}} '''Iperf InstaGENI UCLA VM to GPO InstaGENI VM (TCP) - TCP window size: 23.5 KByte (default)''' ''Collected: 2014-11-18'' __One Client_ {{{ }}} __Five Clients__ {{{ }}} __Ten Clients__ {{{ }}} '''Iperf InstaGENI UCLA VM to GPO InstaGENI VM (UDP) - UDP buffer size: 224 KByte (default) ''' {{{ }}} '''Ping from InstaGENI UCLA VM to GPO InstaGENI VM ''' {{{ }}} == IG-ST-2 New Site to GPO IG Loop topology == Create a slice and then create the stitched slivers with the RSpec [http://groups.geni.net/geni/browser/trunk/stitch-examples/UCLA/IG-ST-2.rspec IG-ST-2.rspec]: {{{ omni.py createslice IG-ST-2 stitcher.py createsliver IG-ST-2 IG-ST-2.rspec -o }}} Determined login information at each UCLA and GPO aggregate: {{{ $ readyToLogin.py IG-ST-2 -a ucla-ig .... $ readyToLogin.py IG-ST-2 -a gpo-ig .... }}} Login to GPO host and ping the remote on each of the two interfaces. Below is the ping output for the GPO site: {{{ ping 10.10.4.2 -c 60 -q ping 192.168.4.2 -c 60 -q }}} == IG-ST-3 IG-ST-3 New Site 3 node linear topology == Create a slice and then create the stitched slivers with the RSpec [http://groups.geni.net/geni/browser/trunk/stitch-examples/UCLA/IG-ST-3.rspec IG-ST-3.rspec]: {{{ omni.py createslice IG-ST-3 stitcher.py createsliver IG-ST-3 IG-ST-3.rspec -o }}} Determined login information the UCLA host: {{{ $ readyToLogin.py IG-ST-3 -a ucla-ig .... }}} Login to the UCLA host and ping each remote: {{{ #ping GPO IG ping 192.168.2.1 -c 60 -q # Utah IG ping 192.168.4.1 -c 60 -q }}} == IG-ST-4 New Site to GPO EG interoperability == Create a slice and then create the stitched slivers with the RSpec [http://groups.geni.net/geni/browser/trunk/stitch-examples/UCLA/IG-ST-4.rspec IG-ST-4.rspec], which specifies a 100 Mbps link capacity. This was done to get around the mismatch in link capacity units that exists between IG and EG. {{{ omni.py createslice IG-ST-4 stitcher.py createsliver IG-ST-4 IG-ST-4.rspec -o }}} Determined login information at each UCLA and GPO aggregate: {{{ $ readyToLogin.py IG-ST-4 -a ucla-ig .... $ readyToLogin.py IG-ST-4 -a eg-sm .... }}} === Measurements === '''Iperf ExoGENI GPO VM to InstaGENI UCLA VM (TCP) - TCP window size: 23.5 KByte (default)''' ''Collected: 2014-08-XX'' __One Client_ {{{ }}} __Five Clients__ {{{ }}} __Ten Clients__ {{{ }}} '''Iperf ExoGENI GPO VM to InstaGENI UCLA VM (UDP) - UDP buffer size: 224 KByte (default) ''' {{{ }}} '''Ping from ExoGENI GPO VM to the InstaGENI UCLA VM ''' {{{ }}} '''Iperf InstaGENI UCLA VM to ExoGENI GPO VM (TCP) - TCP window size: 23.5 KByte (default)''' ''Collected: 2014-08-XX'' __One Client_ {{{ }}} __Five Clients__ {{{ }}} __Ten Clients__ {{{ }}} '''Iperf InstaGENI UCLA VM to ExoGENI GPO VM (UDP) - UDP buffer size: 224 KByte (default) ''' {{{ }}} '''Ping from InstaGENI UCLA VM to ExoGENI GPO VM ''' {{{ }}} == IG-ST-5 Site Information == Various pages include stitching information for a site. Each of the following were verified for this site: 1. Verified that stitching VLANs and Device URN information exists in the [http://groups.geni.net/geni/wiki/GeniAggregate/UCLAInstaGENI#GENINetworkStitching UCLA Aggregate] page. 2. Verified that Delegated GENI Stitching VLANs for site are documented at the [https://wiki.maxgigapop.net/twiki/bin/view/GENI/StaticNetworksView Delegated GENI Stitching VLANs]. 3. Stitching Computation Service logs were reviewed while testing stitching to this site, no issues found. 4. Added site to the list of [wiki:GeniNetworkStitchingSites GENI Network Stitching Sites]. == IG-ST-6 New Site !OpenFlow topology == Create a slice and then create the stitched slivers using !OpenFlow with the RSPec [http://groups.geni.net/geni/browser/trunk/stitch-examples/UCLA/IG-ST-6.rspec IG-ST-6.rspec]: {{{ omni.py createslice IG-ST-6 stitcher.py createsliver IG-ST-6 IG-ST-6.rspec -o }}} Determined login information at each UCLA and GPO aggregate: {{{ $ readyToLogin.py IG-ST-6 -a ucla-ig .... $ readyToLogin.py IG-ST-6 -a gpo-ig .... }}} === Measurements === '''Iperf InstaGENI GPO VM to InstaGENI UCLA VM (TCP) - TCP window size: 23.5 KByte (default)''' ''Collected: 2014-xx-xx'' __One Client_ {{{ }}} __Five Clients__ {{{ }}} __Ten Clients__ {{{ }}} '''Iperf InstaGENI GPO VM to InstaGENI UCLA VM (UDP) - UDP buffer size: 224 KByte (default) ''' {{{ }}} '''Ping from InstaGENI GPO VM to InstaGENI UCLA VM ''' {{{ }}} '''Iperf InstaGENI UCLA VM to InstaGENI GPO VM (TCP) - TCP window size: 23.5 KByte (default)''' ''Collected: 2014-xx-xx'' __One Client_ {{{ }}} __Five Clients__ {{{ }}} __Ten Clients__ {{{ }}} '''Iperf InstaGENI UCLA VM to InstaGENI GPO VM (UDP) - UDP buffer size: 224 KByte (default) ''' {{{ }}} '''Ping from InstaGENI UCLA VM to InstaGENI GPO VM ''' {{{ }}} ----- {{{ #!html Email help@geni.net for GENI support or email me with feedback on this page! }}}