1968 | | |
1969 | | 29. Verify that all three experiment continue to run without impacting each other's traffic, and that data is exchanged over the path along which data is supposed to flow. |
1970 | | 30. Review baseline monitoring statistics and checks. |
1971 | | 31. As site administrator, identify all controllers that the BBN InstaGENI !OpenFlow switch is connected to |
1972 | | 32. As Experimenter3, verify that traffic only flows on the network resources assigned to slivers as specified by the controller. |
| 1968 | From ''gpo-ig'' host send traffic to ''utah-pg'': |
| 1969 | {{{ |
| 1970 | [lnevers2@gpo-ig ~]$ ping 10.42.19.198 |
| 1971 | PING 10.42.19.198 (10.42.19.198) 56(84) bytes of data. |
| 1972 | From 10.42.19.33 icmp_seq=1 Destination Host Unreachable |
| 1973 | ??? |
| 1974 | }}} |
| 1975 | |
| 1976 | From ''utah-pg'' host send traffic to ''gpo-ig'': |
| 1977 | {{{ |
| 1978 | [lnevers2@gpo-ig ~]$ ping 10.42.19.198 |
| 1979 | PING 10.42.19.198 (10.42.19.198) 56(84) bytes of data. |
| 1980 | From 10.42.19.33 icmp_seq=1 Destination Host Unreachable |
| 1981 | }}} |
| 1982 | |
| 1983 | From GPO PG node send traffic to ''utah-pg'' host: |
| 1984 | {{{ |
| 1985 | vm:~> ping 10.42.19.44 |
| 1986 | PING 10.42.19.44 (10.42.19.44) 56(84) bytes of data. |
| 1987 | ??? |
| 1988 | }}} |
| 1989 | |
| 1990 | == 29. Verify that experiments continue to run == |
| 1991 | |
| 1992 | Verified that all 3 experiments continue to exchange traffic without impacting each other's traffic. Experiment 1 and Experiment2 working, resolving issue with Experiment 3. |
| 1993 | |
| 1994 | == 30. Review baseline monitoring == |
| 1995 | |
| 1996 | == 31. As site administrator, identify all controllers == |
| 1997 | |
| 1998 | No site administrative features are available for this test case, so verified controller connections for known controllers. |
| 1999 | The BBN InstaGENI !OpenFlow switch is ''06:d6:84:34:97:c6:c9:00'' and was connected to the following controller: |
| 2000 | {{{ |
| 2001 | lnevers@mallorea:~$ ./nox-console -n localhost -p 11018 getnodes | grep 06:d6:84:34:97:c6:c9:00 |
| 2002 | 06:d6:84:34:97:c6:c9:00 |
| 2003 | lnevers@mallorea:~$ ./nox-console -n localhost -p 11017 getnodes | grep 06:d6:84:34:97:c6:c9:00 |
| 2004 | 06:d6:84:34:97:c6:c9:00 |
| 2005 | lnevers@mallorea:~$ ./nox-console -n localhost -p 11018 getnodes | grep 06:d6:84:34:97:c6:c9:00 |
| 2006 | 06:d6:84:34:97:c6:c9:00 |
| 2007 | lnevers@mallorea:~$ ./nox-console -n localhost -p 11019 getnodes | grep 06:d6:84:34:97:c6:c9:00 |
| 2008 | 06:d6:84:34:97:c6:c9:00 |
| 2009 | lnevers@mallorea:~$ |
| 2010 | }}} |
| 2011 | |
| 2012 | == 32. As Experimenter3, verify that traffic flows == |
| 2013 | As Experimenter 3 (lnevers2@bbn.com) verified that traffic is only allowed for network resources ad defined for the slivers and no traffic can be exchanged across the different experiments. |
| 2014 | |
1975 | | 34. Set the hard and soft timeout of flowtable entries |
1976 | | 35. Get switch statistics and flowtable entries for slivers from the !OpenFlow switch. |
1977 | | 36. Get layer 2 topology information about slivers in each slice. |
1978 | | 37. Install flows that match only on layer 2 fields, and confirm whether the matching is done in hardware. |
1979 | | 38. If supported, install flows that match only on layer 3 fields, and confirm whether the matching is done in hardware. |
1980 | | 39. Run test for at least 4 hours. |
1981 | | 40. Review monitoring statistics and checks as above. |
1982 | | 41. Delete slivers. |
| 2017 | |
| 2018 | == 34. Set the hard and soft timeout of flowtable entries == |
| 2019 | |
| 2020 | == 35. Get switch statistics and flowtable entries == |
| 2021 | Get switch statistics and flowtable entries for each of the experiments from the InstaGENI !OpenFlow switch. |
| 2022 | |
| 2023 | == 36. Get layer 2 topology information == |
| 2024 | Get layer 2 topology information about slivers in each slice. |
| 2025 | |
| 2026 | == 37. Install flows layer 2 flows == |
| 2027 | Install flows that match only on layer 2 fields, and confirm whether the matching is done in hardware. |
| 2028 | |
| 2029 | == 38. Install flows layer 3 flows == |
| 2030 | |
| 2031 | If supported, install flows that match only on layer 3 fields, and confirm whether the matching is done in hardware. |
| 2032 | |
| 2033 | == 39. Run test for at least 4 hours == |
| 2034 | |
| 2035 | == 40. Review monitoring == |
| 2036 | Review monitoring statistics and checks as above. |
| 2037 | |
| 2038 | == 41. Delete all slivers == |
| 2039 | |