= EG-EXP-4: ExoGENI Multi-site Acceptance Test = This page captures status for the test case EG-EXP-4, which verifies the ability to support basic operations of VMs and data flows between two racks. For overall status see the [wiki:GENIRacksHome/ExogeniRacks/AcceptanceTestStatus ExoGENI Acceptance Test Status] page. = Test Status = This section captures the status for each step in the acceptance test plan. || '''Step''' || '''State''' || '''Date completed''' ||''' Ticket ''' || '''Comments''' || || Step 1 || || || || || || Step 2 || || || || || || Step 3 || || || || || || Step 4 || || || || || || Step 5 || || || || || || Step 6 || || || || || || Step 7 || || || || || || Step 8 || || || || || || Step 9 || || || || || || Step 10 || || || || || || Step 11 || || || || || || Step 12 || || || || || || Step 13 || || || || || || Step 14 || || || || || || Step 15 || || || || || || Step 16 || || || || || || Step 17 || || || || || [[BR]] || '''State Legend''' || '''Description''' || || [[Color(green,Pass)]] || Test completed and met all criteria || || [[Color(#98FB98,Pass: most criteria)]] || Test completed and met most criteria. Exceptions documented || || [[Color(red,Fail)]] || Test completed and failed to meet criteria. || || [[Color(yellow,Complete)]] || Test completed but will require re-execution due to expected changes || || [[Color(orange,Blocked)]] || Blocked by ticketed issue(s). || || [[Color(#63B8FF,In Progress)]] || Currently under test. || [[BR]] = Test Plan Steps = Test case is modified to use EXOSM to request resources across sites. The nickname: {{{ exosm=,https://geni.renci.org:11443/orca/xmlrpc }}} is used in place of the site' SMs: {{{ exo-bbn=,https://bbn-hn.exogeni.net:11443/orca/xmlrpc exo-rci=,https://rci-hn.exogeni.net:11443/orca/xmlrpc }}} Also, for initial test run only VMs used. == Step 1. As Experimenter1, Request !ListResources RENCI ExoGENI == {{{ $ ./src/omni.py -a exosm listresources -o }}} == Step 2. Review !ListResources output == Reviewed content of output file named rspec-geni-renci-org-11443-orca.xml. == Step 3. Define a request RSpec == Define a request RSpec for a VM at BBN ExoGENI, a VM at RENCI ExoGENI and an unbound exclusive non-!OpenFlow VLAN to connect the 2 endpoints. == Step 4. Create the first slice. == Using the following command: {{{ $ ./src/omni.py createslice experiment1 }}} == Step 5. Create a sliver == Using the ExoSM and the RSpecs defined above issued: {{{ $ ./src/omni.py -a exosm createsliver experiment1 ./exorspec/EG-EXP-4_exp1.rspec }}} == Step 6. Log in to each of the systems, and send traffic to the other system, leave traffic running == == Step 7. As Experimenter2, Request !ListResources from RENCI ExoGENI == == Step 8. Define a request RSpec == Full step description: "Define a request RSpec for one VM and one bare metal node each with two interfaces in the BBN ExoGENI rack, two VMs at RENCI, and two VLANs to connect the BBN ExoGENI to the RENCI ExoGENI." == Step 9. Create a second slice == == Step 10. In the second slice, create a sliver at the RENCI ExoGENI aggregate using the RSpecs defined above == == Step 11. Log in to each of the end-point systems, and send traffic to the other end-point system which shares the same VLAN == == Step 12. Verify traffic handling per experiment, VM isolation, and MAC address assignment == == Step 13. Construct and send a non-IP ethernet packet over the data plane interface. == == Step 14. Review baseline monitoring statistics == == Step 15. Run test for at least 4 hours == == Step 16. Review baseline monitoring statistics == == Step 17. Stop traffic and delete slivers ==