Changes between Version 20 and Version 21 of GENIRacksHome/AcceptanceTests/ExogeniAcceptanceTestsPlan

Timestamp:

04/11/12 17:00:55 (12 years ago)

Author:

lnevers@bbn.com

Comment:

--

GENIRacksHome/AcceptanceTests/ExogeniAcceptanceTestsPlan

@@ -244 +244 @@
 Do the following:
 
- 1. As Experimenter1, Request !ListResources from BBN ExoGENI.
- 2. Request !ListResources from RENCI ExoGENI.
- 3. Review !ListResources output from both AMs.
- 4. Define a request RSpec for a VM at BBN ExoGENI.
- 5. Define a request RSpec for a VM at RENCI ExoGENI and an unbound exclusive non-!OpenFlow VLAN to connect the 2 endpoints. 
- 6. Create the first slice.
- 7. Create a sliver at each ExoGENI aggregate using the RSpecs defined above.
- 8. Log in to each of the systems, and send traffic to the other system, leave traffic running.
- 9. As Experimenter2, Request !ListResources from BBN ExoGENI and RENCI ExoGENI.
- 9. Define a request RSpec for one VM and one bare metal node in the BBN ExoGENI rack. Each resource should have two logical interfaces. 
- 10. Define a request RSpec to add two VMs at RENCI and two VLANs to connect the BBN ExoGENI to the RENCI ExoGENIs.
- 11. Create a second slice.
- 12. In the second slice, create a sliver at each ExoGENI aggregate using the RSpecs defined above.
- 13. Log in to each of the end-point systems, and send traffic to the other end-point system which shares the same VLAN.
- 14. Verify traffic handling per experiment, VM isolation, and MAC address assignment.
- 15. Construct and send a non-IP ethernet packet over the data plane interface.
+ 1. As Experimenter1, Request !ListResources RENCI ExoGENI.
+ 2. Review !ListResources output.
+ 3. Define a request RSpec for a VM at BBN ExoGENI, a VM at RENCI ExoGENI and an unbound exclusive non-!OpenFlow VLAN to connect the 2 endpoints. 
+ 4. Create the first slice.
+ 5. Create a sliver at the RENCI ExoGENI aggregate using the RSpecs defined above.
+ 6. Log in to each of the systems, and send traffic to the other system, leave traffic running.
+ 7. As Experimenter2, Request !ListResources from RENCI ExoGENI.
+ 8. Define a request RSpec for one VM and one bare metal node each with two interfaces in the BBN ExoGENI rack, two VMs at RENCI, and two VLANs to connect the BBN ExoGENI to the RENCI ExoGENI.
+ 9. Create a second slice.
+ 10. In the second slice, create a sliver at the RENCI ExoGENI aggregate using the RSpecs defined above.
+ 11. Log in to each of the end-point systems, and send traffic to the other end-point system which shares the same VLAN.
+ 12. Verify traffic handling per experiment, VM isolation, and MAC address assignment.
+ 13. Construct and send a non-IP ethernet packet over the data plane interface.
+ 14. Review baseline monitoring statistics.
+ 15. Run test for at least 4 hours.
  16. Review baseline monitoring statistics.
- 17. Run test for at least 4 hours.
- 18. Review baseline monitoring statistics.
- 19. Stop traffic and delete slivers.
+ 17. Stop traffic and delete slivers.
 
 Note: After a successful test run, this test will be revisited and the procedure will be re-executed as a longevity test for a minimum of 24 hours rather than 4 hours.