wiki:GENIExperimenter/Tutorials/PortalSimpleLayer2Example/ExecuteExperiment

Version 14 (modified by sedwards@bbn.com, 7 years ago) (diff)

--

Getting Started with GENI using the GENI Portal

Experiment Workflow

Execute Experiment: Login to the nodes and execute a simple layer 2 experiment

1. Login to nodes

Login information for a VM
  1. Return to the Slice page. Press the Details button in the row of the slice table for GPO InstaGENI.
  2. Open a new terminal window. Copy the command to the right of Login into that terminal window. You have now logged into your VM.
  3. Return to the Slice page and repeat the previous two steps for Utah InstaGENI in a second terminal window.

2. Run your experiment

  1. Send IP traffic The first simple experiment that we will run is to verify the IP connectivity between our hosts.
    1. Check the interfaces of your nodes. In the terminal type:
         /sbin/ifconfig
      
      You should see at least two interfaces:
      • The control interface. This is the interface from where you access the node, e.g. ssh into your host. The control interface is mainly used for control traffic, i.e. traffic for controlling the node and the experiment. The control interface usually has a publicly routable IP.
      • The data interface. This is the interface that is used for sending experimental traffic. This is the interface that connects to the other hosts of your experiment through GENI. The links between these interfaces are the ones that allow you to run non-IP experiments.
    2. Fill in the worksheet, noting the name and IP address of the control and of the data interfaces for each node. The data interface is the one that has an IP that starts with 10.
    3. When we reserved the resources, we did not specify the IP address for the data interfaces. Instead, do this now. Configure the IP address on the data interface of each node using the desired data IP address from the worksheet :
          sudo /sbin/ifconfig <data i/f name> <desired data IP addr>/24
      
      For example:
          sudo /sbin/ifconfig mv.7.90 10.10.1.1/24
      
    4. Use /sbin/ifconfig to confirm the new IP address and mask for each node.
    5. From the client, ping the server. From the xterm that is logged in to the client type :
          ping <server data IP addr> -c 5
      
      For example:
          ping 10.10.1.2 -c 5
      
      An example output should look like :
      [[inki@r2 ~]$ ping 10.10.1.1 -c 5
      PING 10.10.1.1 (10.10.1.1) 56(84) bytes of data.
      64 bytes from 10.10.1.1: icmp_seq=1 ttl=64 time=1.95 ms
      64 bytes from 10.10.1.1: icmp_seq=2 ttl=64 time=2.27 ms
      64 bytes from 10.10.1.1: icmp_seq=3 ttl=64 time=2.04 ms
      64 bytes from 10.10.1.1: icmp_seq=4 ttl=64 time=1.95 ms
      64 bytes from 10.10.1.1: icmp_seq=5 ttl=64 time=1.72 ms
      
      --- 10.10.1.1 ping statistics ---
      5 packets transmitted, 5 received, 0% packet loss, time 4005ms
      rtt min/avg/max/mdev = 1.728/1.992/2.278/0.179 ms
      
  1. Send non-IP traffic. GENI provides the capability of running non-IP experiments, since you can connect your hosts at Layer 2. For the purpose of this tutorial we have installed in all the hosts a very simple Layer 2 ping program that sends packets using a custom ethernet type.
    1. Disable the IP in your nodes. First of all we are going to completely disable IP on our nodes. In each of the terminals type:
        sudo /sbin/ifconfig <data i/f name> 0.0.0.0
      
      Note: Be extra careful to bring down the IP on the data interface, bringing down the IP on the control interface means that you will lose connectivity to your host.
    2. Try again to ping from the client to the server. In the xterm of the client type:
          ping <server data IP addr> -c 5
      
      For example:
          ping 10.10.1.2 -c 5
      
      This time the ping should timeout.
    3. Start the Layer 2 ping server: In the server xterm, type:
        sudo /usr/local/bin/pingPlusListener <EtherType from worksheet>
      
    4. From the client try to ping the server at layer 2. You will need the mac address of the data interface of the server, the name of the data interface of the client, and the EtherType from your worksheet. In the xterm of the client, type:
        sudo /usr/local/bin/pingPlus <server data mac addr> <client data i/f name> <EtherType from worksheet>
      
      The result should look like :
      [uncusr20@client ~]$ sudo /usr/local/bin/pingPlus 02:00:9B:48:3E:20 mv1.1 10001
      RQ:'5582+2067' to 2:0:9b:48:3e:20.
      RQ:5582+2067 from 2:0:3e:15:6c:ab.
      

3. Logout of your nodes

  • When you are done, type exit in each of your open terminals.

Congratulations you have run a Layer 2 experiment in GENI!

Next Part: Teardown Experiment